The S-480-24 is a 24V 20A switching power supply unit. It converts AC mains power into a stable 24V DC output. Its rated output power is 480W. The unit uses an enclosed metal case with a perforated cover and a built-in cooling fan. As a result, it suits control panels, LED lighting systems, CCTV installations and automation projects.
In short, the 24V 20A power supply delivers one regulated DC output from a single compact unit. It also includes protection circuits for short circuit, overload, over-voltage and over-temperature.
What the S-480-24 Does
A switching power supply works differently from a traditional linear transformer. First, it rectifies the incoming AC voltage. Next, it switches that DC at high frequency. Then, a compact high-frequency transformer steps the voltage down. Finally, the output is rectified, filtered and regulated to 24V DC.
Because of this design, the S-480-24 is lighter and smaller than a linear supply of the same rating. In addition, it wastes less energy as heat. Typical efficiency for this class of 24V 20A power supply is around 85–88%.
Output Power and Voltage Regulation
The S-480-24 supplies a rated 24V DC at up to 20A. This gives a total of 480W.
- Rated current: 20A continuous at 24V
- Adjustable output: a front trimmer (marked V.ADJ) sets the voltage within about ±10%
- Adjustment range: roughly 21.6V to 26.4V
- Ripple and noise: typically 150–200mVp-p at full load
The adjustment trimmer is useful in practice. For example, long cable runs cause voltage drop. Therefore, an installer can raise the output slightly to compensate at the far end of the line. Similarly, the trimmer helps when charging or floating some 24V battery systems that need a precise voltage.
However, the total output should stay within 480W. Raising the voltage does not raise the power limit. Consequently, the available current falls slightly at higher output voltages.
AC Input and Kenyan Mains Compatibility
The 24V 20A power supply accepts standard AC mains input. Most S-480-24 units use a selector switch for 110V or 220V input. Other versions use a universal input range.
- Input voltage: 110VAC / 220VAC, selectable (±15%)
- Input frequency: 47–63Hz
- Inrush current: cold start current is limited by the input circuit
Kenyan mains runs at 240V, 50Hz. Therefore, the selector switch must sit on the 220V position before power-up. Leaving it on 110V and connecting to 240V mains will damage the unit. For this reason, check the switch on every new installation.
In addition, KPLC supply often shows voltage dips and surges. The ±15% input tolerance gives the S-480-24 some headroom against these swings. Even so, a surge protector or AVR upstream is a sensible addition at sites with unstable power.
Protection Circuits
The S-480-24 includes four main protection features. Together, they protect both the power supply and the connected load.
- Short circuit protection: the output shuts down or enters hiccup mode when a short is detected. It recovers automatically once the fault is removed.
- Overload protection: triggers at around 105–150% of rated load. The unit then limits or cycles the output until the load drops.
- Over-voltage protection: clamps the output if voltage rises to around 27.6–32.4V. This guards sensitive 24V equipment.
- Over-temperature protection: reduces or cuts the output if internal temperature rises too high.
As a result, a wiring fault on one device does not usually destroy the 24V 20A power supply. Likewise, the connected equipment is protected from runaway voltage.
Cooling and Thermal Design
At 480W, the S-480-24 produces a meaningful amount of heat. For this reason, it uses forced-air cooling.
- A built-in DC fan pulls air through the enclosure.
- The aluminium base acts as a heat sink.
- A perforated steel cover allows airflow across the components.
Meanwhile, the unit is rated for operation from about -10°C to +60°C. Above roughly 45–50°C, the output should be derated. In practice, this means loading the S-480-24 below 20A in hot enclosures. Leaving at least 10–15cm of clearance around the fan and vents helps maintain full output.
Terminals and Wiring
The S-480-24 uses a screw terminal block along one edge. Typically, the layout is:
- L – AC live input
- N – AC neutral input
- ⏚ / FG – protective earth
- -V (x3) – DC negative output
- +V (x3) – DC positive output
The multiple output terminals let you split the 20A across several cable runs. For example, one pair can feed an LED strip while another feeds a controller. Additionally, an LED indicator shows when DC output is present.
Always connect the earth terminal. The metal case relies on it for electrical safety.
Isolation and Safety
The 24V 20A power supply isolates the AC input from the DC output. This isolation is tested at high voltage during manufacture.
- Input to output: typically withstands 1.5kVAC
- Input to case: typically withstands 1.5kVAC
- Output to case: typically withstands 0.5kVAC
- Isolation resistance: ≥100MΩ at 500VDC
Consequently, the low-voltage DC side remains separated from mains voltage. This matters for systems that people may touch, such as LED fixtures and access control readers.
Mounting and Physical Design
The S-480-24 is built for fixed installation. Its threaded holes on the base and sides allow screw mounting in a cabinet or on a backboard. Also, its slim profile fits inside standard electrical and CCTV enclosures.
Typical dimensions are about 215 × 115 × 50mm. Weight is around 0.9–1.1kg. Because the case is not sealed, the unit is meant for indoor use or inside a weatherproof enclosure.
Who Is the S-480-24 Best Suited For?
- CCTV and security installers – The 20A output can run many 24V DC devices from one point. For instance, PTZ cameras, IR illuminators and access control boards often use 24V. Furthermore, the three output terminal pairs simplify distribution to several devices.
- LED lighting contractors – 24V LED strips commonly draw 0.5–1A per metre on bright runs. Therefore, 480W can power long signage or cove lighting runs. The voltage trimmer also helps offset drop on long strips.
- Industrial and automation technicians – PLCs, relays, sensors and solenoid valves often run on 24V DC. The over-voltage protection (around 27.6–32.4V) protects these controls. Additionally, the 1.5kVAC isolation separates control wiring from mains.
- Gate, barrier and door automation installers – Many 24V DC motor systems need high current at startup. The 20A rating and overload headroom (about 105–150%) handle short inrush loads better than smaller supplies.
- Electronics workshops and makers – The 480W rating powers 3D printer heated beds, CNC controllers and test benches. Meanwhile, the adjustable output covers roughly 21.6–26.4V for varied loads.
- Telecom and networking setups – 24V DC feeds some radios and network equipment. Paired with a UPS or battery backup, the S-480-24 helps keep these systems running during KPLC interruptions.
Frequently Asked Questions
How many watts is a 24V 20A power supply? A 24V 20A power supply delivers 480W (24V × 20A).
Can the S-480-24 work on Kenyan 240V mains? Yes. Set the input selector switch to 220V before connecting it. The ±15% tolerance covers 240V supply.
Can I run a 24V 20A power supply at full load continuously? Yes, within the rated temperature range. Above about 45–50°C ambient, reduce the load to prevent overheating.
How many 24V LED strip metres can the S-480-24 power? It depends on strip wattage. As a guide, keep the total load at about 80% of 480W, which is roughly 384W, for longer component life.
Is the S-480-24 waterproof? No. It has a ventilated enclosure. Install it indoors or inside a weatherproof cabinet.

