Ubiquiti UniFi USW-Enterprise-48-PoE – 48-Port 2.5GbE Layer 3 PoE+ Switch with 10G SFP+

KSh255,000 Ex VAT

The Ubiquiti UniFi USW-Enterprise-48-PoE is a 1U Layer 3 switch with forty-eight 2.5GbE PoE+ ports and four 10G SFP+ uplinks. Its 720W PoE budget powers a full floor of access points, cameras, and phones.

48 × 2.5GbE RJ45 ports – all 802.3af/at PoE+
720W total PoE budget
4 × 10G SFP+ uplink ports
Layer 3: inter-VLAN routing, static routes, DHCP server and relay
160 Gbps non-blocking throughput, 4 MB buffer, 32K MAC table
QoS and Pro AV profiles (Dante, NDI, Q-SYS and more)
Internal 870W PSU with DC input for USP-RPS backup

Ubiquiti USW-Enterprise-48-PoE 48-port 2.5GbE PoE+ switch
Ubiquiti UniFi USW-Enterprise-48-PoE – 48-Port 2.5GbE Layer 3 PoE+ Switch with 10G SFP+
KSh255,000 Ex VAT

The Ubiquiti UniFi USW-Enterprise-48-PoE is a fully managed Layer 3 switch with forty-eight 2.5 Gigabit Ethernet ports. Every one of those ports supplies 802.3at PoE+ power, drawn from a 720W PoE budget. In addition, four 10G SFP+ ports provide fibre uplinks.

In practical terms, the USW-Enterprise-48-PoE powers and connects an entire floor of access points, cameras, and phones from one 1U rack unit. Furthermore, its 2.5GbE ports remove the 1 Gbps ceiling that limits Wi-Fi 6 and Wi-Fi 6E access points on standard switches.

What the USW-Enterprise-48-PoE Does in a Network

Large sites such as hotels, hospitals, and multi-storey offices run dozens of powered devices per floor. On a standard Gigabit switch, two problems appear. First, Wi-Fi 6 access points can exceed 1 Gbps of throughput. Second, the PoE budget runs out long before the ports do.

The USW-Enterprise-48-PoE addresses both. Each of its 48 ports runs at up to 2.5 Gbps and supplies PoE+. Meanwhile, the 720W budget is large enough to power nearly every port at once.

Moreover, the USW-Enterprise-48-PoE routes between VLANs locally. As a result, traffic between floors’ camera, voice, and staff networks does not have to pass through the gateway.

48 × 2.5GbE PoE+ Ports

All forty-eight RJ45 ports on the USW-Enterprise-48-PoE are multi-gigabit and powered. Each port supports 10 Mbps, 100 Mbps, 1 Gbps, and 2.5 Gbps.

This matters for several reasons:

  • Wi-Fi 6 and 6E access points with 2.5GbE uplinks can run above 1 Gbps without a bottleneck at the switch
  • Existing Cat5e and Cat6 cabling supports 2.5GbE over typical in-building distances, so a speed upgrade does not require re-cabling
  • Older 1G devices such as phones, cameras, and PCs connect normally, because each port auto-negotiates its speed

In addition, every port supplies 802.3af/at PoE+. The ports are auto-sensing, so non-powered devices such as PCs receive data only.

PoE Budget: What 720W Can Power

The total PoE budget on the USW-Enterprise-48-PoE is 720W. This works out to 15W per port when all 48 ports are in use. In other words, most deployments can power every port without running out.

For example, typical loads include:

  • IP desk phones – usually 3W to 6W each
  • Fixed IP bullet or dome cameras – often 4W to 8W each
  • Wi-Fi 6 access points – often 13W to 25W each

As a result, a floor with 24 access points, 16 cameras, and 8 phones fits comfortably within 720W. However, each port is PoE+ only. Therefore, devices that need 802.3bt PoE++, such as large PTZ cameras, require a PoE++ switch or injector.

Four 10G SFP+ Uplink Ports

The four SFP+ ports run at 10 Gbps or 1 Gbps. They accept multi-mode fibre, single-mode fibre, DAC cables, and 10G RJ45 modules (sold separately).

This means you can:

  • Uplink to a core switch such as the USW-Aggregation over 10G fibre
  • Bond two or four SFP+ ports with LACP for a 20 Gbps or 40 Gbps uplink with failover
  • Connect a NAS, NVR, or server directly at 10 Gbps
  • Link to another building over single-mode fibre

Consequently, the uplink capacity matches the access ports. Forty-eight access points pushing traffic at once do not choke on a single 1G uplink.

Switching Performance

The USW-Enterprise-48-PoE is built for dense traffic. Here is what the figures mean:

  • 320 Gbps switching capacity. This is (48 × 2.5 Gbps + 4 × 10 Gbps) × 2 for full duplex.
  • 160 Gbps non-blocking throughput. Every port can run at full speed simultaneously.
  • 238 Mpps forwarding rate. This handles heavy small-packet traffic such as VoIP and camera control streams.
  • 4 MB packet buffer. This is eight times the buffer of the Lite range. It absorbs bursts from many access points and cameras at once.
  • 32,000-entry MAC address table. This supports large networks with thousands of devices across many floors.

Layer 3 Routing Features

The USW-Enterprise-48-PoE is a Layer 3 switch for local networks. Its routing features include:

  • Inter-VLAN routing between networks on the switch
  • Static routing between local networks, with up to 256 IPv4 static routes
  • DHCP server for locally managed networks
  • DHCP relay to forward requests to a central DHCP server

For example, guest Wi-Fi, CCTV, VoIP, and staff VLANs on one floor can be routed at the switch. Therefore, the gateway handles only internet-bound traffic, which reduces its load.

Layer 2, QoS, and Pro AV Features

In addition to routing, the USW-Enterprise-48-PoE carries the full UniFi Layer 2 feature set, plus QoS and audio-visual profiles:

  • Up to 1,000 VLANs plus Voice VLAN
  • QoS (DSCP) for prioritising voice and video traffic
  • Pro AV profiles for Dante, Q-SYS, NDI, SDVoE, Shure, AES67, Crestron, and Play
  • LACP link aggregation for bonded uplinks
  • STP and RSTP with loop protection
  • IGMP snooping with querier, fast leave, and router port options
  • 802.1X control for port-based access
  • DHCP snooping and guarding to block rogue DHCP servers
  • MAC-based and IP-based ACLs (128 entries each) with device and network isolation
  • Port isolation, port mirroring, and MAC-based port restriction
  • Storm control, egress rate limiting, flow control, and multicast/broadcast rate limiting
  • Jumbo frames and LLDP-MED

The Pro AV profiles are particularly useful for conference centres, churches, and hotels running networked audio and video. They apply the correct multicast and QoS settings for each AV protocol, rather than requiring manual setup.

Managed Through UniFi Network

The USW-Enterprise-48-PoE is managed in the UniFi Network application (version 6.2.26 and later) and the UniFi mobile app. Once adopted, you can set VLANs, routing, port profiles, and PoE settings from one dashboard.

Moreover, you can power-cycle any PoE port remotely. This is useful when an access point or camera on an upper floor stops responding.

In addition, the front panel has a 1.3″ colour touchscreen. It shows the switch’s IP address, adoption state, and port activity. White LEDs show link and activity on every RJ45 and SFP+ port.

Power Supply and DC Power Backup

The USW-Enterprise-48-PoE has an internal 870W power supply. It runs from 100–240V AC mains.

The switch draws 150W without PoE load and up to 870W with full PoE output. Heat output is 511.8 BTU/hr, excluding PoE.

In addition, the switch has a DC input for the UniFi SmartPower Redundant Power System (USP-RPS, sold separately). The RPS takes over if the internal supply fails. Therefore, a power supply fault does not take down every device on the floor.

For Kenyan sites, power planning matters at this scale. During KPLC outages, a fully loaded USW-Enterprise-48-PoE can draw close to 870W. Consequently, the UPS must be sized for the full PoE load, not just the switch itself. We recommend an online UPS for this class of switch, alongside the RPS for supply redundancy.

Build Quality and Environmental Ratings

The USW-Enterprise-48-PoE is a 1U, 19″ rackmount switch built from SGCC steel. It is 400 mm deep and supports rack depths from 600 mm to 1,200 mm. As a result, it needs a full-depth server rack, not a shallow wall-mount cabinet.

The enclosure carries ESD protection of ±16 kV air and ±12 kV contact discharge. The switch is rated for -5°C to 40°C and 10–90% non-condensing humidity.

Because the unit handles up to 870W, comms room cooling matters. This is especially true in warmer locations such as Mombasa, where room temperature can approach the 40°C limit without air conditioning.

USW-Enterprise-48-PoE vs. USW-24-PoE

Buyers often compare the USW-Enterprise-48-PoE with Ubiquiti’s standard rackmount PoE switches:

  • USW-24-PoE: 24 × 1GbE, 16 × PoE+, 95W budget, 2 × 1G SFP, Layer 2
  • USW-Enterprise-48-PoE: 48 × 2.5GbE, 48 × PoE+, 720W budget, 4 × 10G SFP+, Layer 3, RPS backup

In short, the USW-24-PoE suits a small office floor with modest PoE needs. The USW-Enterprise-48-PoE suits dense, high-traffic floors where every port needs power and Wi-Fi 6 needs more than 1 Gbps.

Frequently Asked Questions

How many PoE ports does the USW-Enterprise-48-PoE have?

All 48 RJ45 ports supply 802.3af/at PoE+.

What is the PoE budget of the USW-Enterprise-48-PoE?

The total PoE budget is 720W, shared across all 48 ports.

What speed are the USW-Enterprise-48-PoE ports?

Each RJ45 port supports up to 2.5 Gbps, and also runs at 1 Gbps, 100 Mbps, and 10 Mbps. The four SFP+ ports run at 10 Gbps or 1 Gbps.

Does the USW-Enterprise-48-PoE support PoE++?

No. The USW-Enterprise-48-PoE supports PoE and PoE+ (802.3af/at). Devices that need 802.3bt PoE++ require a different switch or an injector.

Is the USW-Enterprise-48-PoE a Layer 3 switch?

Yes. It supports inter-VLAN routing, static routing (256 IPv4 routes), DHCP server, and DHCP relay for local networks.

Does the USW-Enterprise-48-PoE support redundant power?

Yes. It has a DC input for the UniFi USP-RPS redundant power system, which is sold separately.

Who Is the USW-Enterprise-48-PoE Best Suited For?

  • Hotels and serviced apartments. Forty-eight PoE+ ports and a 720W budget power an access point in every room on a floor, with 2.5GbE for Wi-Fi 6 speeds.
  • Hospitals and clinics. Layer 3 routing, 802.1X, and 1,000 VLANs separate clinical, admin, guest, and IoT networks, while RPS backup protects against supply faults.
  • Universities, schools, and campuses. 2.5GbE ports support high-density Wi-Fi 6 in lecture halls, and four 10G SFP+ uplinks link buildings over fibre.
  • Large CCTV deployments. Forty-eight powered ports, a 4 MB buffer, and IGMP snooping carry dozens of camera streams to the NVR over 10G uplinks.
  • Conference centres, churches, and AV integrators. Pro AV profiles for Dante, NDI, Q-SYS, and others simplify networked audio and video setup.
  • Multi-storey offices. One 1U switch per floor replaces two or three 24-port units, with Layer 3 routing reducing gateway load.
  • IT contractors and MSPs. UniFi Network, remote PoE power-cycling, and the touchscreen simplify deployment and support at scale.

USW-Enterprise-48-PoE Technical Specifications

General

SpecificationDetail
BrandUbiquiti
Product LineUniFi Switching – Enterprise
ModelUSW-Enterprise-48-PoE
Switch TypeFully managed Layer 3 multi-gigabit PoE+ switch
Form Factor1U rackmount (19″)
ComplianceNDAA compliant

Interfaces

SpecificationDetail
RJ45 Ports48 × 2.5GbE (10M/100M/1G/2.5G)
SFP+ Ports4 × 10G SFP+ (10G/1G)
Management InterfaceEthernet in-band
Display1.3″ LCM colour touchscreen
ControlsFactory reset button

PoE

SpecificationDetail
PoE Ports48 (all RJ45 ports)
PoE StandardIEEE 802.3af / 802.3at (PoE / PoE+)
PoE PinoutPins 1, 2+; 3, 6-
Max. PoE per Port32W (tech specs) / 34.2W (datasheet) – see verification note
PoE Voltage Range44–57V (802.3af), 50–57V (802.3at)
Total PoE Budget720W
PoE++ (802.3bt)Not supported

Performance

SpecificationDetail
Switching Capacity320 Gbps
Total Non-Blocking Throughput160 Gbps
Forwarding Rate238 Mpps (238.095 Mpps)
Packet Buffer Size4 MB
MAC Address Table Size32,000 entries
Supported VLANs1,000
Access ListsIPv4: 128 / MAC: 128