The Ubiquiti UniFi USW-24-PoE is a fully managed Layer 2 switch with twenty-four Gigabit Ethernet ports. Sixteen of those ports supply 802.3at PoE+ power, sharing a 95W PoE budget. In addition, two 1G SFP ports provide fibre uplinks.
In practical terms, the USW-24-PoE connects and powers a whole office floor from one 1U rack unit. It supplies phones, access points, and cameras, while the remaining ports serve PCs, printers, and servers.
What the USW-24-PoE Does in a Network
As an office grows, small switches multiply. A few 8-port units in different corners soon become hard to manage. Furthermore, each one needs its own power socket and uplink.
The USW-24-PoE replaces them with a single rackmount switch. As a result, cabling runs back to one comms cabinet, and one device handles 24 connections.
Moreover, because the USW-24-PoE is a UniFi switch, it appears in the same dashboard as your UniFi gateway and access points. Therefore, VLANs and port profiles are set once and applied across the network.
24 Gigabit Ports: 16 PoE+ and 8 Standard
The USW-24-PoE has twenty-four RJ45 ports. Each port supports 10, 100, and 1000 Mbps.
The port split is as follows:
- 16 × PoE+ ports (802.3af/at). These power IP phones, Wi-Fi access points, and IP cameras.
- 8 × standard Gigabit ports. These connect PCs, printers, servers, NVRs, or the router uplink.
In addition, the PoE+ ports are auto-sensing. They supply power only to devices that request it. This means a PC plugged into a PoE port receives data only.
PoE Budget: What 95W Can Power
The total PoE budget on the USW-24-PoE is 95W. This is shared across all sixteen PoE+ ports. In other words, sixteen PoE ports does not mean sixteen high-power devices.
For example, typical loads include:
- IP desk phones – usually 3W to 6W each
- Fixed IP bullet or dome cameras – often 4W to 8W each
- UniFi Wi-Fi access points – most draw 6W to 13W each
As a result, sixteen IP phones at around 5W each fit within 95W. Similarly, a mix of eight cameras and four access points is realistic. However, sixteen access points would exceed the budget. For this reason, we recommend adding up each device’s rated power before purchase.
If you need more PoE power per switch, Ubiquiti’s Pro and Enterprise 24-port models offer larger budgets.
Two 1G SFP Uplink Ports
The USW-24-PoE includes two SFP ports running at 1 Gbps. These accept 1G fibre modules for multi-mode or single-mode cable.
This means you can:
- Link to another building or floor over fibre, beyond the 100 m copper limit
- Uplink to a core switch without using one of the 24 RJ45 ports
- Bond both SFP ports with LACP for a 2 Gbps uplink with failover
Note that these are 1G SFP ports, not 10G SFP+. Therefore, sites planning a 10G backbone should consider a Pro-series switch instead.
Switching Performance
The USW-24-PoE switches all ports at Gigabit line rate. Here is what the figures mean:
- 52 Gbps switching capacity. This is twenty-six ports (24 RJ45 + 2 SFP) × 1 Gbps × 2 (full duplex).
- 26 Gbps non-blocking throughput. Every port can send and receive at full speed at the same time.
- 39 Mpps forwarding rate. This covers small-packet traffic such as VoIP calls without dropped frames.
- 0.5 MB packet buffer. This absorbs short bursts of traffic.
- 8,000-entry MAC address table. This is ample for a single office or floor.
Layer 2 Management and Security Features
The USW-24-PoE carries the full UniFi Layer 2 feature set. This means you can separate and secure traffic for staff, guests, cameras, and phones.
Key features include:
- Up to 1,000 VLANs plus Voice VLAN for separating staff, guest, CCTV, and VoIP traffic
- LACP link aggregation for bonded uplinks
- STP and RSTP with loop protection to stop broadcast storms
- IGMP snooping with querier, fast leave, and router port options for multicast video
- 802.1X control for port-based access
- DHCP snooping and guarding to block rogue DHCP servers
- MAC-based and IP-based ACLs (128 entries each) with device and network isolation
- Port isolation, port mirroring, and MAC-based port restriction
- Storm control, egress rate limiting, flow control, and multicast/broadcast rate limiting
- Jumbo frames and LLDP-MED for automatic phone and device discovery
Inter-VLAN routing is handled by your UniFi gateway, since the USW-24-PoE is a Layer 2 switch.
Managed Through UniFi Network
The USW-24-PoE is configured in the UniFi Network application (version 7.2.94 and later) and the UniFi mobile app. Once adopted, you can assign VLANs, apply port profiles, and monitor traffic on each port.
Furthermore, you can power-cycle any PoE port remotely. For example, a frozen camera or access point can be restarted without a site visit.
In addition, the front panel has a 1.3″ colour touchscreen. It shows the switch’s IP address, adoption state, and port activity at a glance. Port LEDs show PoE, link speed, and activity.
Fanless 1U Rackmount Design
The USW-24-PoE is a 1U, 19″ rackmount switch built from SGCC steel. Rack-mount brackets are included. Alternatively, it can sit on a desk or shelf.
According to Ubiquiti’s datasheet, the switch uses a fanless thermal design. As a result, it runs silently, which suits comms cabinets placed in offices or reception areas. However, Ubiquiti advises that fanless switches must not be stacked directly on top of each other. Therefore, leave a gap or a blanking panel between units in the rack.
The chassis is 200 mm deep and supports rack depths from 400 mm to 1,200 mm. This means it fits standard wall-mount cabinets as well as floor-standing racks.
Built-In Power Supply and Power Draw
The USW-24-PoE has an internal 120W power supply. It runs directly from 100–240V AC mains, so there is no external adapter.
The switch draws 25W without PoE load and up to 120W with full PoE output. Heat output is 85.3 BTU/hr, excluding PoE.
For Kenyan offices that rely on a UPS or inverter during KPLC outages, size the UPS for the full PoE load. In return, one UPS on the USW-24-PoE keeps phones, Wi-Fi, and cameras online during a power cut.
Build Quality and Environmental Ratings
The steel enclosure carries ESD protection of ±16 kV air and ±12 kV contact discharge. It also meets ETSI 300-019-1.4 for shock and vibration.
The USW-24-PoE is rated for -5°C to 40°C and 10–90% non-condensing humidity. Since it is fanless, airflow around the unit matters, particularly in warmer locations such as Mombasa.
USW-24-PoE vs. USW-Lite-16-PoE vs. USW-Pro-8-PoE
Buyers often compare the USW-24-PoE with other UniFi PoE switches:
- USW-Lite-16-PoE: 16 × GbE, 8 × PoE+, 45W budget, no SFP, desktop/wall
- USW-24-PoE: 24 × GbE, 16 × PoE+, 95W budget, 2 × 1G SFP, 1U rackmount
- USW-Pro-8-PoE: 8 × GbE, 2 × PoE++ and 6 × PoE+, 120W budget, 2 × 10G SFP+, Layer 3
In short, the USW-24-PoE suits sites that need many ports and many low-to-mid-power PoE devices in a rack. Sites with high-draw devices or a 10G backbone should look at the Pro range.
Frequently Asked Questions
How many PoE ports does the USW-24-PoE have?
The USW-24-PoE has sixteen PoE+ ports. The other eight RJ45 ports are standard Gigabit ports without PoE.
What is the PoE budget of the USW-24-PoE?
The total PoE budget is 95W, shared across the sixteen PoE+ ports.
Does the USW-24-PoE have SFP ports?
Yes. It has two 1G SFP ports for fibre uplinks. These do not support 10G SFP+ modules.
Is the USW-24-PoE fanless?
Yes. Ubiquiti’s datasheet describes a fanless, silent thermal design. However, Ubiquiti advises against stacking fanless switches directly on top of each other.
Can the USW-24-PoE be rack mounted?
Yes. The USW-24-PoE is a 1U, 19″ rackmount switch, and rack-mount brackets are included.
Is the USW-24-PoE a Layer 3 switch?
No. The USW-24-PoE is a managed Layer 2 switch. Inter-VLAN routing is handled by the UniFi gateway.
Who Is the USW-24-PoE Best Suited For?
- Growing offices consolidating switches. Twenty-four Gigabit ports in one 1U unit replace several small switches and centralise cabling in one cabinet.
- Offices with IP telephony. Sixteen PoE+ ports and a 95W budget power up to sixteen low-draw IP phones, while Voice VLAN and LLDP-MED automate phone setup.
- Schools, clinics, and hotels. 1,000 VLANs and 802.1X separate staff, guest, and admin networks across a floor or block.
- CCTV comms rooms. Sixteen PoE+ ports power fixed cameras, eight non-PoE ports connect NVRs, and IGMP snooping manages multicast video.
- Multi-building sites. Two 1G SFP ports carry fibre uplinks between blocks, beyond the 100 m copper limit.
- Comms cabinets near work areas. The fanless design runs silently, and the 200 mm chassis fits shallow wall-mount cabinets.
- IT contractors and MSPs. UniFi Network, remote PoE power-cycling, and the touchscreen simplify setup and support across client sites.

