The Ubiquiti UniFi USW-Pro-8-PoE is a compact, fully managed Layer 3 switch. It has eight Gigabit RJ45 ports, all of which supply PoE. In addition, it has two 10G SFP+ ports for fast uplinks.
In practical terms, the USW-Pro-8-PoE powers high-draw devices that smaller switches cannot. Two ports deliver up to 60W of PoE++, while six deliver PoE+. Together, they share a 120W PoE budget.
What the USW-Pro-8-PoE Does in a Network
Entry-level PoE switches work well for phones and small cameras. However, PTZ cameras, outdoor access points, and video intercoms often need more power per port. They also need a faster link back to the core.
The USW-Pro-8-PoE covers both needs. First, it powers every one of its eight ports. Second, its two 10G SFP+ ports link it to a core switch, such as the USW-Aggregation, or to a NAS. As a result, eight Gigabit devices never compete for a single 1G uplink.
Furthermore, the USW-Pro-8-PoE adds Layer 3 features. It can route between VLANs and run DHCP for local networks itself. Consequently, inter-VLAN traffic does not have to travel to the gateway and back.
Eight PoE Ports: 2 × PoE++ and 6 × PoE+
All eight RJ45 ports on the USW-Pro-8-PoE supply power. Each port runs at 10, 100, or 1000 Mbps.
The PoE split is as follows:
- 2 × PoE++ ports (802.3bt). Each can deliver up to 60W. These suit PTZ cameras, outdoor or high-performance access points, and small displays.
- 6 × PoE+ ports (802.3af/at). Each can deliver up to 30W. These suit standard access points, fixed cameras, and IP phones.
In addition, every PoE port is auto-sensing. It only supplies power when the connected device requests it. Therefore, PCs and printers can safely use any port.
PoE Budget: What 120W Can Power
The total PoE budget on the USW-Pro-8-PoE is 120W. This is more than double the budget of the USW-Lite-8-PoE (52W). In other words, you can load every port with real devices.
For example, a typical mixed load could include:
- Two PTZ cameras on the PoE++ ports – often 25W to 40W each
- Four UniFi access points – most draw 6W to 13W each
- Two IP phones or fixed cameras – usually 4W to 8W each
As a result, a site with both high-draw and standard devices fits on one switch. However, the budget is still shared. We therefore recommend adding up the rated power of each device before purchase.
Two 10G SFP+ Uplink Ports
The two SFP+ ports run at 10 Gbps or 1 Gbps. They accept multi-mode fibre, single-mode fibre, DAC cables, and 10G RJ45 modules (sold separately).
This means you can:
- Uplink to a core switch over fibre at 10 Gbps
- Connect a NAS or NVR directly at 10 Gbps
- Bond both ports with LACP for a 20 Gbps uplink with failover
- Daisy-chain to another switch in a separate room or building
Consequently, the USW-Pro-8-PoE works as an edge switch in a larger fibre network, not only as a standalone desk switch.
Switching Performance
The USW-Pro-8-PoE switches all ports at full line rate. Here is what the figures mean:
- 56 Gbps switching capacity. This covers eight 1G ports plus two 10G ports, all at full duplex.
- 28 Gbps non-blocking throughput. Every port can run at full speed at the same time.
- 42 Mpps forwarding rate. This handles small-packet VoIP and camera control traffic without drops.
- 1.5 MB packet buffer. This is three times the buffer of the Lite range. It absorbs bursts, such as several cameras pushing video at once.
- 16,000-entry MAC address table. This is double the Lite range, so it supports larger networks.
Layer 3 Routing Features
The USW-Pro-8-PoE is a Layer 3 switch for local networks. This sets it apart from the USW-Lite-8-PoE and USW-Lite-16-PoE.
Its Layer 3 features include:
- Inter-VLAN routing between networks on the same switch
- Static routing between local networks, with up to 256 IPv4 static routes
- DHCP server for locally managed networks
- DHCP relay to forward requests to a central DHCP server
For example, CCTV traffic between a camera VLAN and an NVR VLAN can be routed at the switch. Therefore, video does not need to pass through your gateway, which reduces its load.
Layer 2 Management and Security Features
In addition to routing, the USW-Pro-8-PoE carries the full UniFi Layer 2 feature set:
- Up to 1,000 VLANs plus Voice VLAN
- LACP link aggregation for bonded uplinks
- STP and RSTP with loop protection
- IGMP snooping with querier, fast leave, and router port options
- 802.1X control for port-based access
- DHCP snooping and guarding to block rogue DHCP servers
- MAC-based and IP-based ACLs (128 entries each) with device and network isolation
- Port isolation, port mirroring, and MAC-based port restriction
- Storm control, egress rate limiting, flow control, and multicast/broadcast rate limiting
- Jumbo frames and LLDP-MED
Managed Through UniFi Network
The USW-Pro-8-PoE is managed in the UniFi Network application (version 7.5.176 and later) and the UniFi mobile app. Once adopted, you can set VLANs, routing, and port profiles from one dashboard.
Moreover, you can power-cycle any PoE port remotely. This is useful when a PTZ camera or access point stops responding at a site you cannot reach quickly.
In addition, the front panel has a 1.3″ colour touchscreen. It shows the switch’s IP address, adoption state, and port activity at a glance.
Built-In Power Supply and Compact Design
The USW-Pro-8-PoE has an internal 150W power supply. It runs directly from 100–240V AC mains. Therefore, there is no external power brick.
The switch draws 30W without PoE load and up to 150W with full PoE output. Heat output is 102.4 BTU/hr, excluding PoE.
For Kenyan sites that rely on a UPS or inverter during KPLC outages, plan for the full PoE load. However, because the switch powers your cameras and access points directly, one correctly sized UPS keeps the whole edge of the network running.
Physically, the unit measures 200 × 248 × 44 mm and weighs 2.1 kg. As a result, it fits on a desk, a shelf, or a wall. The enclosure combines polycarbonate and metal.
Environmental Ratings
The USW-Pro-8-PoE is rated for ambient temperatures from -5°C to 45°C and 10–90% non-condensing humidity. This 45°C upper limit is 5°C higher than the Lite range.
Even so, leave space around the unit for airflow. This matters most inside closed cabinets and in warmer locations such as Mombasa.
USW-Pro-8-PoE vs. USW-Lite-8-PoE
Buyers often compare the USW-Pro-8-PoE with the USW-Lite-8-PoE:
- USW-Lite-8-PoE: 8 × GbE, 4 × PoE+, 52W budget, no SFP, Layer 2, external adapter
- USW-Pro-8-PoE: 8 × GbE, 2 × PoE++ and 6 × PoE+, 120W budget, 2 × 10G SFP+, Layer 3, internal PSU, touchscreen
In short, the USW-Lite-8-PoE suits a small office with a few low-power devices. The USW-Pro-8-PoE suits sites with high-draw devices, a fibre backbone, or VLAN routing needs.
Frequently Asked Questions
How many PoE ports does the USW-Pro-8-PoE have?
All eight RJ45 ports supply PoE. Two support PoE++ at up to 60W, and six support PoE+ at up to 30W.
What is the PoE budget of the USW-Pro-8-PoE?
The total PoE budget is 120W, shared across all eight ports.
Is the USW-Pro-8-PoE a Layer 3 switch?
Yes. The USW-Pro-8-PoE supports inter-VLAN routing, static routing (256 IPv4 routes), DHCP server, and DHCP relay for local networks.
Does the USW-Pro-8-PoE have SFP+ ports?
Yes. It has two 10G SFP+ ports. SFP+ modules and DAC cables are sold separately.
Does the USW-Pro-8-PoE need an external power adapter?
No. The USW-Pro-8-PoE has a built-in 150W power supply and connects directly to a 100–240V AC socket.
Can the USW-Pro-8-PoE power non-UniFi cameras such as Hikvision PTZs?
Yes. The ports follow IEEE 802.3af/at/bt standards. Therefore, standards-based PoE, PoE+, and PoE++ devices can be powered, within the per-port and 120W total limits.
Who Is the USW-Pro-8-PoE Best Suited For?
- CCTV installers. Two 60W PoE++ ports power PTZ cameras, while 10G SFP+ uplinks carry multi-camera video to the NVR or core without bottlenecks.
- Offices with a fibre backbone. Two SFP+ ports connect to a core switch such as the USW-Aggregation, with LACP bonding for a 20 Gbps uplink.
- Sites with many VLANs. Inter-VLAN routing and a local DHCP server reduce load on the gateway for CCTV, VoIP, staff, and guest networks.
- High-density Wi-Fi rollouts. A 120W budget supports several access points on one switch, with PoE++ headroom for higher-draw models.
- Hotels, schools, and estates with outdoor devices. A -5°C to 45°C operating range and PoE++ suit gate intercoms, outdoor access points, and perimeter cameras fed from a nearby cabinet.
- IT contractors and MSPs. UniFi Network, remote PoE power-cycling, and the touchscreen speed up setup and support across client sites.

